Home › Blog › Attached garage separation: IRC R302.5 and R302.6 explained
Code Explainers

Attached garage separation: IRC R302.5 and R302.6 explained

Half-inch board, 5/8-inch Type X over rooms, a self-closing door, and steel ducts. What the 2024 IRC changed.

InstaPreView · Published November 16, 2026 · Updated November 16, 2026
Line drawing of a floor plan with a hatched fire-rated separation wall between two spaces, titled “Attached garage separation: IRC R302.5 and R302.6 explained”. InstaPreView by Byts & Bytes.

A plan reviewer marks up the floor plan of a new house: "Provide 5/8-inch Type X gypsum board at the garage ceiling. Bonus room above." The designer had shown 1/2-inch board on the garage side of every wall and the ceiling. That works for a single-story house. It does not work once someone can stand in a room over the garage.

The rules for the wall, ceiling, door, and ducts between a house and its attached garage are short, and they sit in two sections of the IRC. Here is what the 2021 IRC says, and what the 2024 edition changed.

The separation table

2021 IRC Section R302.6 says the garage shall be separated as required by Table R302.6. The table has four rows:

  • From the residence and attics: not less than 1/2-inch gypsum board or equivalent, applied to the garage side.
  • From habitable rooms above the garage: not less than 5/8-inch Type X gypsum board or equivalent.
  • Structure supporting floor/ceiling assemblies used for the separation: not less than 1/2-inch gypsum board or equivalent.
  • Garages less than 3 feet from a dwelling unit on the same lot: not less than 1/2-inch gypsum board or equivalent on the interior side of the exterior walls within that area.

Three details in the same section get missed:

  • The wall separation rows do not apply to garage walls that are perpendicular to the adjacent dwelling unit wall.
  • Gypsum board attachment has to follow Table R702.3.5, so fastener type and spacing belong in the detail, not just the board type.
  • The third row means beams, girders, and bearing walls that carry the ceiling over the garage need at least 1/2-inch board too. A 5/8-inch Type X ceiling hung from an unprotected flush beam is not the whole answer.

None of the rows asks for a fire-resistance rating. The table names a material, not an hour.

The door

Section R302.5.1 sets two rules for openings:

  1. No opening from a private garage directly into a room used for sleeping. A door from the garage straight into a bedroom is not allowed with any door rating.
  2. Other openings need one of these doors: solid wood not less than 1-3/8 inches thick, solid or honeycomb-core steel not less than 1-3/8 inches thick, or a 20-minute fire-rated door. The door has to be self-latching and have a self-closing or automatic-closing device.

The door schedule is where this fails in review. "Solid core" is not the same as "solid wood," and a schedule that lists the garage door without a closer leaves the reviewer to ask.

Ducts and other penetrations

  • Ducts (R302.5.2): ducts in the garage, and ducts that penetrate the walls or ceilings between the dwelling and the garage, must be at least No. 26 gage sheet steel or other approved material, and they cannot have openings into the garage. A supply register in the garage served by the house system fails this.
  • Everything else (R302.5.3): pipes, cables, and other penetrations through the separation are protected as required by Section R302.11, Item 4. That item calls for an approved material at openings around vents, pipes, ducts, cables, and wires, to resist the free passage of flame and products of combustion.

Two more garage rules worth putting on the plans

  • Egress (R311.1): the means of egress must reach the required egress door without requiring travel through a garage. A house whose only exterior door is through the garage does not comply.
  • Floor (R309.1): the garage floor must be an approved noncombustible material, and the parking area has to slope so liquids move to a drain or toward the main vehicle entry door.

What the 2024 IRC changed

The 2024 IRC keeps the same door, duct, and gypsum board requirements. The wording changed:

  • Sections R302.5 and R302.6 now say "dwelling unit" where 2021 said "residence" or "dwelling."
  • The 5/8-inch Type X row now reads "from portions of the dwelling unit above the garage" instead of "from habitable rooms above the garage." Read literally, the 2024 row covers any part of the dwelling unit over the garage, not only habitable rooms, so a storage room of the house above the garage reads in too. Confirm how your reviewer applies it.
  • The garage and carport section moved from R309 to Section R317.

Where this goes on the drawings

  • A wall type or note for the garage side of each common wall and the garage ceiling, with board type and thickness.
  • A note covering the beams and bearing walls that support the ceiling over the garage.
  • A door schedule entry for each house-to-garage door: construction, thickness or rating, self-latching, and closer.
  • A mechanical note for duct gage at the garage, with no registers in the garage.

The model code is a starting point. Check your city's adopted IRC edition and amendments on the code adoption tracker or the jurisdiction pages. For the wall between two units in a duplex or townhouse, see dwelling unit separation ratings. For commercial work, the fire-resistance-rated construction guide and the firestopping guide cover IBC rules.

Run a free scan on a house plan. A bonus room over a garage with a 1/2-inch board ceiling note is the kind of comment the scan can surface before a reviewer does.

This is advisory. It is not a determination by the authority having jurisdiction. Confirm the adopted edition and local amendments before you change a drawing.