Home › Blog › The addition meets the energy code. The house does not have to.
Code Explainers

The addition meets the energy code. The house does not have to.

2021 IECC Section R502: what a residential addition carries, and what changes when a garage becomes a room.

InstaPreView · Published November 15, 2026 · Updated November 15, 2026
Line drawing of a wall section showing studs, cavity insulation and continuous insulation, titled “The addition meets the energy code. The house does not have to.”. InstaPreView by Byts & Bytes.

The energy sheet for a 400-square-foot family room addition lists new R-values for the addition and one note: "Existing house to remain." Under the 2021 IECC that note can be right. The addition has to meet the code for new construction. The rest of the house does not, unless the project changes it.

Section R502.1: three ways an addition complies

2021 IECC Section R502.1 requires an addition to conform to the code as it relates to new construction, "without requiring the unaltered portion of the existing building or building system to comply with this code." It then says an addition is deemed to comply where:

  • the addition alone complies,
  • the existing building and the addition comply as a single building, or
  • the building with the addition does not use more energy than the existing building.

Section R501.1.1 backs that up: unaltered portions of the existing building are not required to comply. Section R401.2 points additions, alterations, repairs, and changes of occupancy to Chapter 5 instead of the Chapter 4 compliance paths.

The prescriptive list in Section R502.3

  • R502.3.1 Building envelope. New envelope assemblies in the addition comply with Sections R402.1, R402.2, R402.3.1 through R402.3.5, and R402.4. The exception: new envelope assemblies are exempt from the air leakage testing in Section R402.4.1.2.
  • R502.3.2 Heating and cooling. HVAC ducts newly installed as part of the addition comply with Section R403. The exception: ducts extended to the addition from an existing heating and cooling system.
  • R502.3.3 Service hot water. New systems that are part of the addition comply with Section R403.5.
  • R502.3.4 Lighting. New lighting systems that are part of the addition comply with Section R404.1.

The envelope values come from Table R402.1.3 for the climate zone. The residential envelope calculator reads that table with the ICC errata applied, and the post on the 2021 IECC wall insulation errata explains why the wall row in your copy may be out of date.

The garage or porch that becomes a room

Section R501.2 sends a change from unconditioned to conditioned space to Section R502. Section R502.2 then says unconditioned or low-energy space altered to become conditioned space is brought into full compliance with the code, with three exceptions:

  1. Using the simulated performance option in Section R405, the proposed design's annual energy cost may be 110 percent of what Section R405.2 otherwise allows.
  2. The Total UA of the existing building, the addition, and any alterations in the project is less than or equal to the Total UA of the existing building.
  3. Under Section R405, the annual energy cost or energy use of the addition and existing building, with the project's alterations, is not more than that of the existing building. The addition and alterations then comply with Section R405 in its entirety.

For a converted garage, show the slab, the walls, the ceiling, and any infilled door opening against the table.

When the addition comes with alterations

Most additions also open up the house. Section R503.1.1 covers envelope assemblies that are part of an alteration. The printed section cites "R402.1.2 or R402.1.4". The ICC errata posted September 6, 2022 for the first and second printings corrects that to R402.1.2 or R402.1.3. Exceptions apply where the energy use of the building is not increased, including:

  • existing ceiling, wall, or floor cavities exposed during construction, provided they are filled with insulation,
  • construction where the existing roof, wall, or floor cavity is not exposed,
  • storm windows over existing fenestration, and roof recover.

Section R503.1.1.1 covers replacement windows. A replacement fenestration unit, including sash and glazing, meets the U-factor and SHGC in Table R402.1.3, and an area-weighted average of all the replacement units is an allowed alternative. Glass-only replacement in an existing sash and frame is a repair under Section R504.2, not an alteration.

Section R503.1.4 brings new lighting in an alteration under Section R404.1. Its exception covers alterations that replace less than 10 percent of the luminaires in a space without increasing interior lighting power.

The alteration versus change of occupancy post and the existing buildings guide cover the building-code side of the same project.

What to put on the drawings

  • The energy code edition, the climate zone, and which R502.1 approach you are using.
  • A clear line on the plan between the addition, altered areas, and unaltered existing areas.
  • For the addition: wall, ceiling, floor, and slab sections with R-values from Table R402.1.3, and the window schedule with U-factor and SHGC.
  • For any space going from unconditioned to conditioned: the R502.2 path, and the Total UA or R405 report if you use an exception.
  • For exposed existing cavities: a note that they will be filled with insulation.
  • Whether the addition's ducts are new or extended from the existing system.

Check the adopted energy code on the code adoption tracker or the jurisdiction pages. States amend the IECC, and the documentation a city wants is covered in the energy compliance documentation guide.

Run a free scan on the addition set. An energy sheet that says "existing to remain" over a garage being converted to a bedroom is the kind of gap the scan can surface before a reviewer does.

This is advisory. It is not a determination by the authority having jurisdiction. Confirm the adopted edition and local amendments before you change a drawing.